NGVideo-5_8GHz-RX
| Documentation / Part Lists | /5.8Hz-TX | /5.8GHz-RX | Back |
Part Lists for the NG Video 5.8GHz RX
Note:: The use and operation of this product in most states, countries requires a HAM or Amateur radio license. NG.UAVP.ch and the devs of this pcb set cannot be held responsible for your actions if you use this product without proper licensing
This is work in progress and preliminary information!
The following tables list the electronic parts needed to build the Video boards.
This ~PartList is sorted by distributor. The distributor is selected by availability and minimum number of distributor which are Reichelt Electronik and Farnell
Browsers for Printing this Partlist:
- Firefox: best browser with landscape orientation und 50% scaling
- Opera: good Result with landscape orientation und automatic scaling
- Internet Explorer: nearly impossible to get the full table printed
Build Options
There are several options you can choose from.
UnderVoltageProtection and single switch channel selector
It is possible to populate an Atmega644 to the rx board to have an under voltage protection and a single switch channel selector.
Attention:: This is not supported at the moment!
You can easyly populate it later when the firmware is ready.
LCD Monitoring
It is possible to populate an LCD to the 5,8ghz pcb for channel selection and status information of the Rx.
Selecting the channel
You can select the receiving channel by the DIP switch or later with the atmega644.
| Dip1 | Dip2 | Dip3 | Frequency | Channel |
| on | on | on | 5740MHz | 1 |
| off | on | on | 5760MHz | 2 |
| on | off | on | 5780MHz | 3 |
| off | off | on | 5800MHz | 4 |
| on | on | off | 5820MHz | 5 |
| off | on | off | 5840MHz | 6 |
| on | off | off | 5860MHz | 7 |
| off | off | off | 5860MHz | 7 |
Video Amplifier
You can populate a video and audio amplifier (reconstruction buffer) to connect more than one video device to your receiver. You should also get a a better video quality.
Attention:: If you have no video amplifier, you have to shorten pin 2 with pin 3 and pin 5 with pin 6 on U100, populate C115 with a 0R resistor or solderbridge and connect jumper SJ100 with an solder brige!
Partlist
Partlist for the 5,8gz TX
Basic parts
Basic parts for the TX
| Name | Value / Manufacturer | Part Type / Description | Package | Quantity | Comments | Reichelt | CSD-Electronic | Farnell | Digikey | Distrelec [CH] | Other |
| X7 | HEBW 21 | connector | 1 | HEBW 21 | 015-564 | ||||||
| S2 | DA03 | switch | 1 | not needed with the atmega | NT 03-90 | nicht gewinkelt: 35-DIP03 | |||||
| D10 | 1n4001 | 1 | 1N 4001 SMD | or 4006: 11026 | |||||||
| C17 | 2,2nf | kerko | 0805 | 1 | X7R-G0805 2,2N | 115-08N002,2 | |||||
| L2 | 10µH | induktivity | PIS2816 | 1 | L-PIS2816 10µ | ||||||
| C19 | 10µF | Elko | 2.5-6 | 1 | Note polarity | RAD 10/35 | 120-R0010V035 | ||||
| R131, R132, R133 | 10k | Resistor | 0805 | 3 | SMD-0805 10,0K | 10-08K010 | |||||
| R3 | 12k | Resistor | 0805 | 1 | SMD-0805 12,0K | 10-08K012 | |||||
| C12, C15 | 22µF | Elko | 2-5 | 2 | Note polarity | RAD 22/16 | 120-R0022V025 | ||||
| R2 | 22k | Resistor | 0805 | 1 | SMD-0805 22,0K | 10-08K022 | |||||
| R4 | 39k | Resistor | 0805 | 1 | SMD-0805 39,0K | 10-08K039 | |||||
| L1 | 100µH | INDUCTOR | PIS4728 | 1 | L-PIS4728 100µ | ||||||
| C1, C2, C3, C7, C14, C16, C22, C23, C25, C102, C126 | 100n | Kerko | 0805 | 11 | X7R-G0805 100N | 115-08N100 | |||||
| C18 | 100p | Kerko | 0805 | 1 | NPO-G0805 100P | 115-08C100 | |||||
| C6, C8, C20, C21 | 220µ | elko | 5-8.5 | 4 | Note polarity | RAD 220/25 | 120-R0220V025 | ||||
| C9 | 220µF | elko | 2.5-6 | 1 | Note polarity | RAD 105 220/16 | |||||
| C4 | 1000µ | elko | 5-13 | 1 | Note polarity | RAD 1.000/25 | 120-R1000V025 | ||||
| IC1 | AWM680RX | 1 | |||||||||
| X1, X4, X6 | chinch | connector | 3 | CBP-G | |||||||
| IC4 | LT1776 | IC | SO-8 | 1 | LT 1776 CS8 | ||||||
| D11 | MBRS140 | Diode | 1 | Note polarity | MBRS 140 SMD | 11154 |
Parts for the Video reconstruction buffer
Parts needed by the Video reconstruction buffer.
If you don’t like to populate the video buffer see note: Video Amplifier
| Name | Value / Manufacturer | Part Type / Description | Package | Quantity | Comments | Reichelt | CSD-Electronic | Farnell | Digikey | Distrelec [CH] | Other |
| L100 | 10µH | Inductor | 1812 | 1 | LQH3C 10µ | ||||||
| R120,R117, R121 | 75ohm | resistor | 1206 | 3 | SMD 1/4W 75 | ||||||
| R123, R124, R125, R126, R127, R128, R129, R130 | 15k | resistor | 0805 | 8 | SMD-0805 15,0K | 10-08K015 | |||||
| C11, C105, C109 | 22µF | tantal | C | 3 | Line is (+) C105: to Q100, C109: to NGvideo, C11: to C10 | SMD TAN.22/6,3 | |||||
| C13, C106, C120 | 100n | kerko | 0805 | 3 | X7R-G0805 100N | 115-08N100 | |||||
| C115, C122, C123, C124, C125 | 100n | Kerko | 1206 | 5 | X7R-G1206 100N | 115-12N100 | |||||
| C10 | 220µF | elko | 2.5-6 | 1 | Note polarity | RAD 105 220/16 | |||||
| X3 | chinch | conector | 1 | CBP-G | |||||||
| IC104 | FMS6141 | IC | so8 | 1 | Pin 1 to the solder bridge SJ100 | 1495487 | |||||
| U100 | OPA2350 | IC | so8 | 1 | OPA 2350 UA |
Parts for the Atmega644
Parts needed for the Atmega644
| Name | Value / Manufacturer | Part Type / Description | Package | Quantity | Comments | Reichelt | CSD-Electronic | Farnell | Digikey | Distrelec [CH] | Other |
| D1, D2, D3, D4, D5, D6, D7, D8, D9 | LED3MM | LED | 3mm | 9 | Not needed with lcd | 115-08N100 | |||||
| R103 | 1k | resistor | 0805 | 1 | SMD-0805 1,00K | ||||||
| R1, R101, R104, R107, R118 | 10k | resistor | 0805 | 5 | SMD-0805 10,0K | 10-08K010 | |||||
| Q100 | 20mhz | quarz | HC49UP | 1 | 20,0000-HC49-SMD | 14-4S20,000 MHZ | |||||
| C117, C118 | 22p | kerko | 0805 | 2 | NPO-G0805 22P | 115-08C022 | |||||
| C24, C100, C101, C112, C119, C121 | 100n | kerko | 0805 | 6 | X7R-G0805 100N | 115-08N100 | |||||
| R100, R105 | 100ohm | resistor | 0805 | 2 | SMD-0805 100 | 10-080100 | |||||
| R102, R106, R108, R109, R112, R113, R116, R119, R122 | 680R | resistor | 0805 | 9 | Not needed with lcd | SMD-0805 680 | 10-080680 | ||||
| X100 | 532610471- 04 | Conector | 532610471- 04 | 1 | |||||||
| IC102 | ATMEGA644- 20A | IC | TQFP | 1 | ATMEGA 644-20 AU | 30173 | |||||
| X2 | pinheader 6 pol. | socket | 1 | ||||||||
| D100 | BAS40-05 / BAR 43C SMD | diode | sot23 | 1 | Note polarity | BAR 43C SMD | |||||
| T100, T101 | BC817 | npn | sot23 | 2 | BC 817-40W SMD | ||||||
| SP1 | buzzer | buzzer | AL60P | 1 | Note polarity | SUMMER TDB 05 | 064-BUZZ5V | ||||
| X5 | MICROMATCH -16 | MICROMATCH -16 | MICROMATCH -16 | 1 | MM FL 16G | ||||||
| S1 | switch | switch | switch | 1 | TASTER 3305B | ||||||
| IC3 | LP2950 5.0 | 1 | LP 2950 ACZ5,0 | 23-381 |
Parts for the LCD (beta version)
Parts needed by the LCD.
| Name | Value / Manufacturer | Part Type / Description | Package | Quantity | Comments | Reichelt | CSD-Electronic | Farnell | Digikey | Distrelec [CH] | Other |
| C3, C4, C8, C9, C10, C11 | 100n | kerko | 0805 | 7 | X7R-G0805 100N | 115-08N100 | |||||
| C1, C2 | 1µF | kerko | 0805 | 2 | X7R-G0805 1,0/25 | 115-08R001 | |||||
| R21, R18 | 1k | resistor | 0805 | 2 | SMD-0805 1,00K | ||||||
| R5, R7, R8, R10, R12, R16 | 4k7 | resistor | 0806 | 6 | SMD-0805 4,70K | ||||||
| R4, R6, R9, R11, R14, R15 | 6k8 | resistor | 0805 | 6 | SMD-0805 6,80K | ||||||
| R2, R3, R13, R19, R20 | 10k | resistor | 0805 | 5 | SMD-0805 10,0K | 10-08K010 | |||||
| C6, C7 | 220µF | elko | SMD_C6 | 2 | opt for servo/ Note polarity | VF 220/16 K-D8 | |||||
| R1 | 220R | resitor | 0805 | 1 | opt for servo | SMD-0805 220 | 10-080220 | ||||
| R17 | 720R | resistor | 0805 | 1 | opt for servo | SMD-0805 680 | 680 Ohm: 10-080680 | ||||
| T1, T2, T3 | bc817 | npn | sot23 | 3 | BC 817-40W SMD | ||||||
| IC100 | DOG-M | lcd | 1 | /!\ backlight panel if needed /!\ see dog-m datasheet | white: EA DOGM163W-A blue:EA DOGM163B-A green:EA DOGM163E-A backlight white: EA LED55X31-W more colors avalable | ||||||
| U1 | LM1117 | ic | 1 | LT 1117 CST-3.3 | 223-1705 | ||||||
| IC1 | LT1963 | ic | 1 | opt-for servo | LT 1963 AEQ | ||||||
| S100, S101, S102 | SKHMPSE010 | switch | 3 | TASTER 9319 | |||||||
| X2 | micromatch 16 smd | connector | 1 | MM FL 16S | |||||||
| micromatch 16 | conector | 2 | to connect the lcd to the RX | MM SL 16SK | |||||||
| cable | 1 | to connect the lcd to the RX | AWG 28-16G 3M | ||||||||
| R100, R101 | 680ohm | resistor | 0805 | 2 | SMD-0805 680 | 10-080680 |
Parts for the diversity option
Parts needed by the diversity option
| Name | Value / Manufacturer | Part Type / Description | Package | Quantity | Comments | Reichelt | CSD-Electronic | Farnell | Digikey | Distrelec [CH] | Other |
| R134, R135, R136 | 10k | resistor | 0805 | 3 | SMD-0805 10,0K | 10-08K010 | |||||
| C107, C108, C110, C111, C113, C114, C116 | 100n | kerko | 0805 | 7 | X7R-G0805 100N | 115-08N100 | |||||
| C103, C104 | 470p | kerko | 0805 | 2 | NPO-G0805 470P | 115-08C470 | |||||
| R110, R111 | 680R | resistor | 0805 | 2 | SMD-0805 680 | 10-080680 | |||||
| R114, R115 | 680k | resistor | 0805 | 2 | SMD-0805 680K | 10-08K680 | |||||
| C5 | 1000µ | elko | 5-13 | 1 | Note polarity | RAD 1.000/25 | 120-R1000V025 | ||||
| IC103 | ADG794 | IC | qsop16 | 1 | 1078226 | ||||||
| IC2 | AWM680RX | IC | 1 | ||||||||
| IC100, IC101 | EL1883 | IC | SO8 | 2 | 1561942 |
Parts for the LCD (new version)
Parts needed by the LCD
| Name | Value / Manufacturer | Part Type / Description | Package | Quantity | Comments | Reichelt | CSD-Electronic | Farnell | Digikey | Distrelec [CH] | Other |
| C3, C4, C5, C9, C11 | 100n | kerko | 0805 | 6 | X7R-G0805 100N | 115-08N100 | |||||
| R21, R18 | 1k | resistor | 0805 | 2 | SMD-0805 1,00K | ||||||
| R2, R3, R13, R19, R20 | 10k | resistor | 0805 | 5 | SMD-0805 10,0K | 10-08K010 | |||||
| C6, C7 | 220µF | elko | SMD_C6 | 2 | opt for servo/ Note polarity | VF 220/16 K-D8 | |||||
| R1 | 220R | resitor | 0805 | 1 | opt for servo | SMD-0805 220 | 10-080220 | ||||
| R17 | 720R | resistor | 0805 | 1 | opt for servo | SMD-0805 680 | 680 Ohm: 10-080680 | ||||
| T1, T2, T3 | bc817 | npn | sot23 | 3 | BC 817-40W SMD | ||||||
| IC100 | DOG-M | lcd | 1 | /!\ backlight panel if needed /!\ see dog-m datasheet | white: EA DOGM163W-A blue:EA DOGM163B-A green:EA DOGM163E-A backlight white: EA LED55X31-W more colors avalable | ||||||
| IC1 | LT1963 | ic | 1 | opt-for servo | LT 1963 AEQ | ||||||
| S100, S101, S102 | SKHMPSE010 | switch | 3 | TASTER 9319 | |||||||
| X2 | micromatch 16 smd | connector | 1 | MM FL 16S | |||||||
| micromatch 16 | conector | 2 | to connect the lcd to the RX | MM SL 16SK | |||||||
| cable | 1 | to connect the lcd to the RX | AWG 28-16G 3M | ||||||||
| R100, R101 | 680ohm | resistor | 0805 | 2 | SMD-0805 680 | 10-080680 |
Case for the Rx FR 80 42 120 ME (Reichelt part number)
Documentation and schematics
- NG-Video-5.8GHz-RX (PDF)
- NG-Video-5.8GHz-RX-Display (PDF)
- Reichelt Bestellliste - Stand 16.8. für den Empfänger (komplette Bestückung)